Conversations

Photo of Reynold
ansible - getting operational structured data from cumulus switch
Hi all, I noticed that Cumulus Switch has a built-in JSON formatting in the NCLU 'net show' command but how to use it using ansible to g...
  • 1 me too
  • 1 reply
  • Question
Photo of Eelco Nieuwstad
ONIE-BOOT not found in CumulusVX3.5
I sm trying to reinstall CumulusVX via ONIE but after downloading the bin file it complains it can't find a device with the name ONIE-BOO...
  • 1 me too
  • 7 replies
  • Question
Photo of Vikram
Route Leaking from vrf to global and vice versa
I followed the instructions ( https://docs.cumulusnetworks.com/display/DOCS/Virtual+Routing+and+Forwarding+-+VRF )  to configure route-le...
  • 1 me too
  • 8 replies
  • Question
Photo of Troy MacDonald
3.4.1 nclu snmp-server commands
Upgraded switch from 3.3.2 to 3.4.1, as I have done half a dozen times recently. However this time, when the upgrade was complete, the ne...
  • 1 me too
  • 9 replies
  • Question
Photo of dlambert88
Technical Documentation - Static VXLAN Tunnels
I was reading the following documentation (https://docs.cumulusnetworks.com/display/DOCS/Static+VXLAN+Tunnels#) and noticed that there ar...
  • 1 me too
  • 2 replies
  • Question
Photo of Diego Pérez Holguín
Breakout a 40G switch port into 4x10G ports, failed to restart switchd
I've followed the instruccions described in technical docummenatation (https://docs.cumulusnetworks.com/display/DOCS/Layer+1+and+Switch+P...
  • 1 me too
  • 2 replies
  • Problem
Photo of Angel
VBOX_E_FILE_ERROR
Hi, I am new to Cumulus and I am trying to import the Cumulus VX into the VirtualBox, However, I am always getting an error like below. ...
  • 1 me too
  • 5 replies
  • Question
Photo of Darshan TM
Login banner message
I want to display the message when the user will login to the switch... basically a banner.. can I know what would be the commas to confi...
  • 1 me too
  • 8 replies
  • Question
Photo of shakir
vx 3.4.0 on the reference topology
i had already downloaded vx3.4.0.box, can i use this with the reference topology @cldemo-vagrant, instead of downloading vx3.3.2...can i ...
  • 1 me too
  • 3 replies
  • Question
Photo of machiasiaweb
Now to rest the port without ifreload?
Hello, When working some wrong setup.  That caused both ADMIN and physical goes to DOWN status. Like ------- 37: swp34: <BROADCAST,MULT...
  • 1 me too
  • 3 replies
  • Question
Photo of machiasiaweb
Only allow VLAN 1 traffic
Hello, I am config the interface now with following setup. --- auto swp34 iface swp34         mstpctl-portadminedge yes         alias n...
  • 1 me too
  • 1 reply
  • Question
Photo of Soeren Hansen
Is there a EOL for support for the AS4610-54T?
Hello, on the Hardware Compatibility List I can see that the EdgeCore  AS4600-54T is only supporting CL up to version 2.5.x. Is there a...
  • 1 me too
  • 4 replies
  • Question
Photo of Troy Kau
The "net show int" command in version 3.3 is extremely slow and information has changed.
Is there a new command that gives the same information that was in 3.2 (interfaces aliases, vlan, bond, bridge info)? Is there work under...
  • 1 me too
  • 4 replies
  • Question
Photo of Christopher Vanik
SHA1 Checksum for Physical Switch Binaries
I'm having a slight issue when I try an ONIE install on physical switch via USB - the SHA1 checksums aren't being validated and this is b...
  • 1 me too
  • 5 replies
  • Problem
Photo of Will McLendon
netq - clarification on no support for mgmt-vrf
Hello, Can anyone clarify the netq documentation that says 'Interoperability with management VRF is not supported' does that mean it's ...
  • 1 me too
  • 2 replies
  • Question
Photo of David
VX - doesn't launch in virtualbox verr_pdm_driver_not_found
Hi there. I'm new to Cumulus and took the liberty of downloading the Virtualbox VX image to try it out. I double clicked on it to import ...
  • 1 me too
  • 4 replies
  • Problem
Photo of Russ Starr
netshow / ethtool issue on VX 3.0.0
$ netshow system NOTE: netshow does not have detailed specs for the 'cumulus,vx' platform Cumulus 3.0.0 Build: Cumulus Linux 3.0.0...
  • 1 me too
  • 3 replies
  • Problem
Photo of David Ramahefason
Upgrading to 3.x from 2.5.7
Hi, do we have to do an ONIE install to go from 2.5.7 to 3.0 ?  did an "apt-update && apt-get upgrade" but this doesn't seem to do the j...
  • 2 me toos
  • 2 replies
  • Question
Photo of Eric Dong
cvx 2.5.7
when will cvx 2.5.7 out? 
  • 1 me too
  • 4 replies
  • Question