Conversations

Photo of Sylvain Munaut
Kernel module source
Hi, I'm looking for the sources of the platform modules ( more specifically accton_as4610_54_cpld and accton_as5712_54x_platform for no...
  • 3 me toos
  • 7 replies
  • Question
Photo of Sylvain Munaut
802.1ae / MacSec
Is there any 10G switch that support 802.1ae / MacSec ?
  • 1 me too
  • 4 replies
  • Question
Photo of Sylvain Munaut
ARP table filling up with public internet IPs ?
I'm a bit confused, when doing arp -n on one of the switch I see a bunch of : 168.195.2.243            ether   00:07:7d:7a:0c:fe   C    ...
  • 2 me toos
  • 4 replies
  • Problem
Photo of Chris Marget
iptables connection tracking for the control plane?
I understand that many iptables features (connection tracking, etc...) are not supported by the underlying switching hardware on switches...
  • 2 me toos
  • 7 replies
  • Question
Photo of machiasiaweb
How to Control Port Speed?
Hello, Could you please advise how to control special port speed which is not common?  Example: 20Mbps, 200Mbps, 300Mbps etc Thanks!
  • 1 me too
  • 4 replies
  • Question
Photo of Sylvain Munaut
ACL POLICE target - What does it do ?
I'm wondering what teh POLICE ip(6)tables target ( & equivalent 'police' ebtable target) do more precisely. Are they terminal rules ? So...
  • 1 me too
  • 3 replies
  • Question
Photo of Sylvain Munaut
Better HW mapping for INPUT ACL chain & How to use stateful matches ?
Something I was thinking about when trying to come up with good . Basically I would have all the 'HW applied' rules in a special chain, ...
  • Sylvain Munaut, 1 year ago

  • 2 me toos
  • 0 replies
  • Idea
Photo of Troy MacDonald
How to get out of mgmt.vrf configuration
This might be a dumb question but I'm stuck and loosing my mind over this: once you configure the mgmt.vrf in 3.2.1 you're brought into a...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Sylvain Munaut
Limiting ACL to specific VLANs when using vlan aware bridge
I can't figure out how to limit an ACL rule to only apply to a specific VLAN when using a single vlan-aware bridge. I tried the --vlan-i...
  • 1 me too
  • 15 replies
  • Question
Photo of Troy MacDonald
Why to configure basic information globally?
What is the 3.2.1 equivalent to Cisco's global configuration?  i.e. switch(config)# ?
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of David Brambila
Is there a way to wipe out configs without having to upgrade or re-provision the system software?
  • 1 me too
  • 4 replies
  • Question
Photo of Sylvain Munaut
How is the Management VRF special ?
Hi, I'm wondering what being a mgmt VRF implied exactly. Mostly what's different between :  * a mgmt VRF + using the default one for "p...
  • 1 me too
  • 2 replies
  • Question
Photo of Sylvain Munaut
TCP multipath - Any alternative to PBR ?
Hi, I'm considering deploying Multi Path TCP for some of our public facing services. If you're not familiar with the concept, the basi...
  • 1 me too
  • 3 replies
  • Question
Photo of Christopher Vanik
SHA1 Checksum for Physical Switch Binaries
I'm having a slight issue when I try an ONIE install on physical switch via USB - the SHA1 checksums aren't being validated and this is b...
  • 1 me too
  • 5 replies
  • Problem
Photo of Scott Suehle
Introducing Cumulus Express — open networking hardware & software all in one
Today we are happy to announce the launch of the Cumulus Express line of network switches. This is an exciting step as we begin the proc...
  • 1 me too
  • 2 replies
  • Article
Photo of Sylvain Munaut
VRR IPv6 ?
For IPv4 first hop redundancy and load balancing, Cumulus supports "VRR". But what about IPv6 ? Does VRR also exist for it ?
  • 1 me too
  • 4 replies
  • Question
Photo of Sylvain Munaut
Will using netlink interface to add/remove ports to VLANs update the HW ?
I need to dynamically add / remove switch ports from vlan, change their PVID and all of that dynamically. I was planning to use pyroute2...
  • 1 me too
  • 5 replies
  • Question
Photo of Sylvain Munaut
ACL in ebtables not behaving as expected
So, just imagine a simple scenario with 2 hosts connected to 2 ports PORTA and PORTB. And I have this in the policy file installed by cl...
  • 1 me too
  • 4 replies
  • Problem